
We Provides repairing services.
Machine Repairing and Servicing by Krishna Engineering Works
Machine repairing and servicing at Krishna Engineering Works covers the working life of a machine after it is built: installation and commissioning at the customer’s site, operator training, spare parts supply, re-covering of rubber rollers, repair and ongoing technical support. The service is given to customers in India and abroad.
The company has manufactured machinery in Ahmedabad, India, since 1990, and makes the machines and their components in its own factory. That is the basis of the service: the factory that built the machine also makes its parts.
What does machine repairing and servicing include?
Machine repairing and servicing includes seven kinds of work, from the first day the machine reaches the site to the routine replacement of wear parts years later. The table sets them out.
| Service | What it covers | When it is needed |
| Trial before dispatch | A continuous trial of the machine at the factory, which the customer is invited to attend | Before the machine leaves Ahmedabad |
| Installation | Positioning, levelling, alignment and connection of the machine at the site | On delivery |
| Commissioning | Startup with the customer’s own material until the machine runs as intended | Straight after installation |
| Operator training | Instruction of operators and maintenance staff on the machine | During commissioning |
| Spare parts supply | Wear parts and replacement components for KEW machines and equipment | Through the life of the machine |
| Rubber roller re-covering | A new rubber covering on the existing roller core | When the covering is worn, cut or hardened |
| Repair and technical support | Fault finding, repair and advice | When a fault or a quality problem appears |
Trial at the factory before dispatch
Service starts before the machine is shipped. Components are inspected from raw material to final assembly, and a continuous trial is taken on the assembled machine before dispatch. Customers are invited to the premises to take a trial of their own machine.
Attending the trial is worth the visit. The buyer’s engineer sees the machine run, checks it against the order, and meets the people who will later commission it. Questions about layout, foundations and services at the site can be settled before the machine arrives, which shortens the installation.
Installation and commissioning at your site
Krishna Engineering Works provides on-site installation and commissioning, and its engineers travel to the customer’s site for startup. This applies to domestic and international customers alike. For export orders the company also handles export documentation and shipping coordination, and gives on-site installation support abroad.
A typical installation follows these steps:
- The customer prepares the floor or foundation, the power supply and any compressed air, water, steam or gas the machine needs.
- The machine is unloaded, positioned and levelled.
- Sections are joined and aligned, so that every roller is square to the web path.
- Electrical and pneumatic connections are made and checked.
- The machine is run empty, then threaded and run slowly with material.
- Tension, guiding and process settings are adjusted on the customer’s own material.
- Speed is raised in steps to the production speed.
- The operators are trained and the machine is handed over.
Good preparation by the customer saves the most time. The services in step 1 should be ready and tested before the engineer arrives, and material for the trial runs should be on hand in the widths and grades that will be run in production.
Operator training
Operator training is given at the customer’s site as part of commissioning. Training on the buyer’s own machine, with the buyer’s own material, is more useful than a classroom session, because the operators learn the settings they will use every day.
Training normally covers the points below. The depth depends on the machine.
- Safe starting, stopping and emergency stopping
- Threading the web and loading and unloading reels or batches
- Setting tension, speed and guiding for each material
- Changeovers between jobs
- Routine cleaning and lubrication
- Recognising the common faults and their first checks
It helps to have the maintenance staff present as well as the operators, and to keep the same people on the machine through the commissioning period.
Spare parts supply
Krishna Engineering Works supplies spare parts for its machines and equipment. Web aligners, rubber rolls and textile spares are made in house, so these parts come from the same factory as the original.
The table lists the usual wear parts by product group, with the page that describes each.
| Product group | Usual wear and spare parts | Where to read more |
| Slitting and rewinding machines | Knives and cutters, shaft parts, nip and lay on rollers | Slitting cutters |
| Air shafts | Valves, hoses, clamps, lugs, inflator guns, rubber tubes | Air shaft |
| Web guiding | Sensor, hydraulic cylinder, filters, power pack parts | Web guiding system |
| Stenter machines | Clips and other stenter parts | Spares of stenter |
| Other textile processing machines | Rolls and machine spares | Spares for textile processing machinery |
| Rollers | Rubber covering, bearings | Rubber roller |
For air shafts, the company supplies valves, hoses, clamps, lugs, inflator guns, rubber tubes and continuous rubber lugs from stock.
To order a spare part quickly, send the machine type, the name of the part and a photograph. Where the part is a roller, shaft or knife, add the main dimensions. If the part has a drawing number on the machine documents, quote it.
Rubber roller re-covering
Re-covering means stripping the worn rubber from a roller and bonding, curing and grinding a new covering on the same metal core. Krishna Engineering Works names re-covering of rubber rollers among its roller services, together with fabrication and precision rollers.
A roller is worth re-covering when the core and journals are sound and only the rubber has failed. The usual signs are:
- The surface has hardened or glazed, so it no longer grips or transfers evenly
- Cuts, chips or edge damage
- Swelling or softening from inks, solvents or chemicals
- Grooves worn where the web edge runs
- The roller is no longer round or has lost its crown
Hardness is measured on the Shore durometer scale, and a covering that has drifted well away from its original hardness will not behave as it did when new. When you send a roller for re-covering, state the compound and hardness you want, the application, and any liquids the roller meets. If you are unsure, describe the job and the fault, and KEW will advise.
The group’s specialist site on rubber roller recoating explains the process step by step.
Repair and technical support
Krishna Engineering Works provides repairing services and ongoing technical support for its customers. Most problems on a running machine fall into a few groups, and a clear description lets the engineer narrow the cause before anyone travels.
| Symptom | Likely area | What to report |
| Web wanders or reel edges are uneven | Web guiding | Sensor position, oil level, whether the stand moves freely |
| Tension varies or the web breaks | Brake, clutch, load cells, drive | When it happens: full reel, empty reel or on speed change |
| Wrinkles in the web | Roller alignment, spreading roll, nip | Where the wrinkle starts and its direction |
| Vibration at speed | Roller balance or bearings | The speed at which it starts, and which section |
| Cores slip on the shaft | Air shaft bladder, valve or lugs | Air pressure held over time, core size |
| Uneven nip or print impression | Rubber roller surface or hardness | Age of the covering, photograph of the surface |
Vibration is worth acting on early. A roller that is out of balance loads its bearings on every turn, and the load rises steeply with speed. The principle is explained under balancing of rotating masses.
Routine care that prevents repairs
Routine care prevents most repairs, and it takes little time if it is done to a schedule. The intervals below are general practice, to be adjusted for the machine, the material and the hours run.
| Interval | Typical tasks |
| Every shift | Clean rollers and sensors, check air pressure, look for web dust and adhesive build up |
| Weekly | Check oil level in the web aligner power pack, check belts and chains, clean filters |
| Monthly | Check bearings for noise and heat, check brake and clutch wear, inspect knife edges |
| Half yearly | Check roller alignment and rubber roller hardness, inspect air shaft bladders and valves |
| Yearly | Plan re-covering of worn rollers and replacement of wear parts during a shutdown |
Keep a small stock of the parts that stop the machine when they fail, such as knives, shaft valves and rubber tubes, and a spare for each critical rubber roller. A spare roller lets the worn one go for re-covering without stopping production.
Which machines does the service cover?
The service covers the machinery and equipment that Krishna Engineering Works manufactures: flexible packaging and converting machinery, textile processing machinery, tyre cord and technical textiles machinery, paper industries machinery, and equipment such as rollers, shafts and web guiding units.
The catalogue of machines is on the products page. Typical examples are the slitter rewinder machine, the lamination machine and the stenter machine. The company’s approach to inspection and trial is described on the quality page.
How to request service
A service request is handled fastest when it arrives complete. Follow these steps:
- Identify the machine: type, size and year of supply if known.
- Describe the fault or the service needed in two or three sentences.
- Add photographs or a short video of the fault and of the machine section.
- For spare parts, name the part and give its dimensions or drawing number.
- For rollers, state the diameter, face length, overall length, compound and hardness.
- Give your location and a contact person at the plant.
Send the request through the contact page or the inquiry form. The company can also be reached by phone on +91-8460728298 and by email at info@kewindia.com.
Frequently Asked Questions
What repairing and servicing does Krishna Engineering Works provide?
Krishna Engineering Works provides on-site installation and commissioning, operator training, spare parts supply, repairing services and ongoing technical support. It also re-covers rubber rollers. The service is available to domestic and international customers, and engineers travel to the customer’s site for startup of a new machine.
Is installation support available outside India?
Yes, Krishna Engineering Works gives on-site installation support abroad. The company is an IEC-certified exporter and handles export documentation and shipping coordination for international orders. Its engineers travel to the customer’s site for startup, and spare parts supply and technical support continue afterwards for international customers as they do for domestic ones.
Can I see my machine running before it is dispatched?
Yes, customers are invited to the company’s premises in Ahmedabad to take a trial of their machine before dispatch. A continuous trial is taken on each machine as part of the quality process. Attending lets your engineer check the machine against the order and settle site questions before the machine is shipped.
How do I order a spare part for a KEW machine?
Order a spare part by sending the machine type, the name of the part and a clear photograph. For rollers, shafts and knives, add the main dimensions, and quote the drawing number if your machine documents show one. Send the details through the contact page, by email or by phone, so the right part can be identified before it is made or dispatched.
When should a rubber roller be sent for re-covering?
A rubber roller should be re-covered when its surface has hardened, glazed, swollen, cut or worn into grooves, or when it is no longer round. These faults show as uneven nip pressure, slipping or marks on the web. If the metal core and journals are sound, a new covering restores the roller.
What should the site have ready before the engineer arrives?
The site should have the floor or foundation finished and the services connected: power, and any compressed air, water, steam or gas the machine needs. The machine should be unloaded near its position, and trial material should be available in production widths and grades. Operators and maintenance staff should be free to attend the commissioning.
Does the service include training for new operators?
Yes, operator training is part of the on-site commissioning that Krishna Engineering Works provides. Operators are trained on their own machine with their own material, covering safe operation, threading, tension and guiding settings, changeovers and routine care. It is useful to have the maintenance staff attend together with the operators.




