
Industrial Roller Manufacturer: Calender, Cooling, Hard Chrome and Steel Rollers
An industrial roller is a precision machined metal roll that carries, presses, heats, cools or finishes a continuous web as it runs through a machine. Krishna Engineering Works manufactures the industrial roller in eight types in Ahmedabad, India, from calender rolls and cooling drums to hard chrome plated, knurled, anodised aluminium and steel rollers.
Each roller is built to the drawing or the line data of the customer. This page describes the eight types, explains how to choose the surface, and lists what to send for a quotation.
What is an industrial roller?
An industrial roller is a rotating cylinder with a shell, two journals and a working surface that is finished for one job on the web. The job decides everything else: an idler only has to turn freely, a cooling roll has to carry water, and a calender roll has to stay straight under heavy nip load.
Metal surfaced rollers do the work that needs hardness, heat transfer or an exact finish. Rollers with an elastic cover belong to a different family, which is described on the rubber roller page. In most nips the two work as a pair, one hard and one soft.
The parts of a metal roller are few:
- Shell. The tube or solid body that forms the face.
- Journals. The shaft ends that sit in the bearings and take the drive.
- End plates. The discs that join shell and journals on a fabricated roller.
- Surface. Plating, anodising, knurling, polishing or plain machining.
- Internal passages. Jackets or spirals for water, oil or steam on heat transfer rolls.
Industrial roller types made by Krishna Engineering Works
Krishna Engineering Works lists eight types of industrial roller. The table summarises what each does, and the sections below describe them.
| Roller type | What it does | Typical position |
| Calender roll | Presses the material to a smooth, even finish | Calender stacks for paper, textile and packaging materials |
| Cooling drum or double jacketed cooling roll | Takes heat out of the web through a water jacket | After extrusion, lamination or drying |
| Suction and spiral cooling rolls | Hold the web by vacuum, or cool it with a spiral water path | Film, coating and lamination lines |
| Dryer cylinder and cooling rollers | Heat the web to dry it, then cool it before winding | Paper mills, printing and textile lines |
| Hard chrome plated roller | Gives a hard, wear resistant, corrosion resistant mirror face | Printing and packaging machines |
| Knurling roller | Grips the web through a patterned face | Pull and feed sections, texturing |
| Hard anodised aluminium roll | Gives a light roll with a hard skin | Idler positions on film and foil lines |
| Stainless steel and MS rollers | Carry heavy loads, or resist wet and corrosive duty | General and heavy duty guide positions |
Calender roll
A calender roll presses the material between two or more rolls to give a smooth finish and an even thickness. KEW builds calender rolls for durability and consistent pressure, for the paper, textile and flexible packaging industries. Because the roll works under high line load, its straightness and surface finish decide the result, as in any calender.
Cooling drum or double jacketed cooling roll
A cooling drum takes heat out of the web. In the double jacketed design the cooling water flows in the narrow space between an outer shell and an inner shell, so it moves fast and stays close to the working face. KEW makes these rolls for heat transfer and cooling during production in the plastic, film and lamination industries. The drums used on tyre cord and textile lines are covered on the cooling and heating drums page.
Suction and spiral cooling rolls
A spiral cooling roll leads the water along a helical path under the shell, which keeps the temperature even from one end of the face to the other. A suction roll holds the web against its face by vacuum through a drilled shell, so the web is gripped without a nip. KEW makes both as special designs for temperature management and web control. A complete station is described on the cooling roll system page.
Dryer cylinder and cooling rollers
A dryer cylinder is a heated roll that dries the web by contact, and it is normally followed by cooling rollers that bring the web back to a safe winding temperature. KEW supplies dryer cylinders and cooling rollers for paper mills and for printing and textile applications, designed for continuous running.
Hard chrome plated roller
A hard chrome plated roller is a steel roll with a plated face that resists wear and corrosion. KEW finishes these rollers to a mirror surface for printing and packaging applications, where a scratch on the roll shows on every metre of product. Chrome plating of this kind is hard and has low friction, so ink and adhesive residue wipe off easily.
Knurling roller
A knurling roller has a precise pattern cut or pressed into its face. The pattern gives grip and texture, so the roller can pull a slippery web without high nip pressure. KEW makes knurling rollers for packaging and industrial applications. The related pull rolls page covers driven draw sections.
Hard anodised aluminium roll
A hard anodised aluminium roll is light, so it turns easily and follows speed changes without scratching the web. The anodised layer gives the soft aluminium a hard, durable skin. KEW supplies these rolls for the film, foil and packaging industries, where most idler positions use them.
Stainless steel and MS rollers
Stainless steel (SS) rollers resist water, steam and chemicals, and mild steel (MS) rollers give strength at lower cost for dry positions. KEW makes both for heavy duty applications that need wear and corrosion resistance.
How do you choose the roller surface?
Choose the surface from what the roller must do to the web: release it, grip it, cool it, or simply carry it. The table gives general selection logic used across the converting industry.
| Requirement at the roller | Surface to consider | Why |
| Clean release of ink, adhesive or coating | Hard chrome plated, mirror finish | Hard, smooth and easy to wipe |
| Light roll that the web can turn by itself | Hard anodised aluminium | Low inertia, hard skin |
| Grip without a heavy nip | Knurled face | Pattern holds a slippery web |
| Fast, even cooling across the width | Double jacketed or spiral cooling roll | Water moves quickly close to the face |
| Wet, steam or chemical duty | Stainless steel | Resists corrosion without plating |
| Heavy load in a dry position | MS roller, plated if needed | Stiff and economical |
| Smooth finish and thickness control | Calender roll | Rigid roll with a fine finish |
Two general points apply to every choice. A smoother face releases better but grips less, so a mirror finish on a driven roll can let a thin film slip. And a matt or grooved finish lets entrained air escape at speed, which is why idlers on fast film lines are often not polished.
Why does a roller need balancing?
A roller needs balancing because any uneven distribution of mass turns into vibration that grows with speed. An unbalanced roll shakes its bearings, marks the web with bars and shortens bearing life. The theory is the same as for any rotating mass.
As general practice, short slow rollers are balanced statically, in one plane. Long rollers and fast rollers are balanced dynamically, in two planes, at or near their working speed. The roller maker needs the maximum line speed and the roller diameter to work out the running speed, so state both in the enquiry.
Balancing is not the only check. Run out of the face, the straightness of the shell and the fit of the journals in the bearings matter just as much. Krishna Engineering Works makes its components in its own factory and inspects them from raw material to final assembly.
Where industrial rollers are used
Industrial rollers are used in every machine that handles a web. KEW names these sectors for its rollers: printing and packaging, pulp and paper, textile, plastic film and foil converting, laminating and coating, and general engineering.
In the company’s own catalogue, a lamination machine presses the webs between a rubber roll and a steel roll and then cools the laminate. A coating machine needs straight, well finished rolls to meter the coating evenly. A slitter rewinder machine carries the web over idlers that must turn freely at speed. Wrinkles ahead of any of these are removed by a bow roll, and web tracking is corrected by tracking roller assemblies.
The group’s specialist site on industrial rollers covers roller engineering in more depth. The complete catalogue is on the products page.
Care and common faults
A metal roller lasts for many years if its face is protected and its bearings are looked after. Most faults seen on the web trace back to one of the causes below.
| Symptom on the line | Likely cause at the roller | First check |
| Regular bars or chatter marks | Imbalance or worn bearings | Vibration at speed, bearing play |
| Scratches along the web | Damaged face, or an idler that has stopped turning | Roll face, free rotation by hand |
| Uneven cooling across the width | Scale or air in the water passage | Flow rate, inlet and outlet temperature |
| Web wanders to one side | Roller not parallel to its neighbours | Alignment with a level and a tape |
| Rust spots or pitting | Plating worn through or damaged | Face under good light |
| Web slips on a driven roll | Face too smooth for the web | Surface finish, wrap angle |
Good general habits help. Clean the face with a soft cloth and a cleaner that suits the surface, never with a blade. Lift rollers by the journals, not by the face. Keep cooling water clean, and store spare rollers on their journals with the face wrapped.
For repair work and re-covering, see repairing and servicing.
How an industrial roller is ordered
An industrial roller is made to order, so the enquiry carries the design. The usual sequence is this.
- Identify the position of the roller on the machine and what it must do there.
- Take the dimensions from the drawing or from the old roller: face length, diameter, overall length and journal details.
- State the surface: plating, anodising, knurl pattern or finish.
- Give the line speed, web tension and any nip load, so the shell and the balancing can be decided.
- For heat transfer rolls, give the heating or cooling medium, its temperature and the connection type.
- Confirm the quantity and whether bearings and housings are needed with the roller.
What to send for an industrial roller quotation
Send the following, with a drawing or a sketch where you have one:
- Roller type and its position on the machine
- Face length, diameter, overall length and journal dimensions
- Shell material: MS, stainless steel or aluminium
- Surface: hard chrome plated, hard anodised, knurled or plain, and the finish needed
- Maximum line speed, web tension and nip load
- For cooling drums and dryer cylinders: medium, temperature and rotary joint details
- Web material and width
- Quantity
Send these through the contact page.
Frequently Asked Questions
What types of industrial rollers does Krishna Engineering Works make?
Krishna Engineering Works makes calender rolls, cooling drums and double jacketed cooling rolls, suction and spiral cooling rolls, dryer cylinders and cooling rollers, hard chrome plated rollers, knurling rollers, hard anodised aluminium rolls, and stainless steel and MS rollers. Each roller is made to the dimensions and the surface the customer specifies.
Which industries use industrial rollers?
Industrial rollers are used in printing and packaging, pulp and paper, textile processing, plastic film and foil converting, laminating and coating, and general engineering. Any machine that moves a continuous web needs them, as idlers that carry the web, as nip rolls that press it, or as heated and cooled rolls that change its temperature.
What are the benefits of a hard chrome plated roller?
A hard chrome plated roller resists wear and corrosion and can be finished to a mirror surface. The hard, smooth face does not mark the web, releases ink and adhesive residue easily, and keeps its finish for a long time. That is why it is the usual choice for printing and packaging machines.
What is a double jacketed cooling roll?
A double jacketed cooling roll is a cooling drum with two shells, one inside the other. The cooling water flows through the narrow gap between them, so it moves quickly and stays close to the working face. This removes heat faster and more evenly than a plain hollow roll that is simply filled with water.
When should an aluminium roller be used instead of a steel roller?
An aluminium roller should be used where the web itself has to turn the roller, as on idler positions of film and foil lines. Aluminium is light, so the roll accelerates easily and does not scratch a thin web. Hard anodising gives it a durable skin. Steel is preferred under heavy load or nip pressure.
Can industrial rollers be made to a custom size and finish?
Yes, Krishna Engineering Works makes industrial rollers in custom sizes, coatings and finishes. The roller is built to the customer’s drawing or to the dimensions of the old roller. Send the face length, diameter, journal details, surface, speed and load, and the design is worked out from that data.
How do I know that a roller is out of balance?
A roller that is out of balance vibrates more as the speed rises, and the vibration usually falls away when the line slows down. You may see regular bars across the web, hear the bearings, or feel the frame shake near that roller. Worn bearings give similar signs, so check both.




